sac5.0 thru sac50 vishay general semiconductor document number: 88379 revision: 20-oct-08 for technical questions within your r egion, please contact one of the following: pdd-americas@vishay.com , pdd-asia@vishay.com , pdd-europe@vishay.com www.vishay.com 1 low capacitance t rans z orb ? transient voltage suppressors features ? glass passivated chip junction ? excellent clamping capability ? 500 w peak pulse power capability with a 10/1000 s waveform, repetitive rate (duty cycle): 0.01 % ? very fast response time ? low incremental surge resistance ? solder dip 260 c, 40 s ? component in accordance to rohs 2002/95/ec and weee 2002/96/ec typical applications use in sensitive electronics protection against voltage transients induced by inductive lo ad switching and lighting on ics, mosfet, signal lines of sensor units for consumer, computer, industrial and telecommunication. mechanical data case: do-204ac, molded epoxy over passivated body molding compound meets ul 94 v-0 flammability rating base p/n-e3 - rohs comp liant, commercial grade terminals: matte tin plated leads, solderable per j-std-002 and jesd22-b102 e3 suffix meets jesd 201 class 1a whisker test polarity: color band denotes tvs cathode end primary characteristics v wm 5.0 v to 50 v p ppm 500 w p d 3.0 w t j max. 175 c do-204ac (do-15) note: (1) non-repetitive current pulse, per fig. 3 and derated above t a = 25 c per fig. 2 maximum ratings (t a = 25 c unless otherwise noted) parameter symbol limit unit peak pulse power dissipatio n with a 10/1000 s waveform (1) p ppm 500 w power dissipation on infi nite heatsink at t l = 75 c (fig. 2) p d 3.0 w peak pulse power surge current with a 10/1000 s waveform (fig. 3) (1) i ppm see next table a operating junction and storage temperature range t j , t stg - 55 to + 175 c www..net
sac5.0 thru sac50 vishay general semiconductor www.vishay.com for technical questions within your region, please contact one of the following: pdd-americas@vishay.com , pdd-asia@vishay.com , pdd-europe@vishay.com document number: 88379 revision: 20-oct-08 2 note: (1) non-repetitive current pulse, per fig. 3 and derated above t a = 25 c per fig. 2 ratings and characteristics curves (t a = 25 c unless otherwise noted) electrical characteristics (t a = 25 c unless otherwise noted) part number stand-off voltage (1) v wm (v) minimum breakdown voltag e at i t = 1.0 ma v br (v) maximum reverse leakage at v wm i d (a) maximum clamping voltag e at i pp = 5.0 a v c (v) maximum peak pulse current per fig. 3 i pp (a) maximum junction capacitance at 0 volts (pf) working inverse blocking voltage v wib (v) inverse blocking leakage current v wib i ib (ma) peak inverse blocking voltage v pib (v) sac5.0 5 7.60 300 10.0 44 50 75 1.0 100 sac6.0 6 7.90 300 11.2 41 50 75 1.0 100 sac7.0 7 8.33 300 12.6 38 50 75 1.0 100 sac8.0 8 8.89 100 13.4 36 50 75 1.0 100 sac8.5 8.5 9.44 50 14.0 34 50 75 1.0 100 sac10 10 11.10 5.0 16.3 29 50 75 1.0 100 sac12 12 13.30 5.0 19.0 25 50 75 1.0 100 sac15 15 16.70 5.0 23.6 20 50 75 1.0 100 SAC18 18 20.00 5.0 28.8 15 50 75 1.0 100 sac22 22 24.40 5.0 35.4 14 50 75 1.0 100 sac26 26 28.90 5.0 42.3 11.1 50 75 1.0 100 sac30 30 33.30 5.0 48.6 10.0 50 75 1.0 100 sac36 36 40.00 5.0 60.0 8.6 50 75 1.0 100 sac45 45 50.00 5.0 77.0 6.8 50 150 1.0 200 sac50 50 55.50 5.0 88.0 5.8 50 150 1.0 200 ordering information (example) preferred p/n unit weight (g) preferred package code base quantity delivery mode sac5.0-e3/54 0.432 54 4000 13" diameter paper tape and reel figure 1. peak pulse power rating curve t d - p u lse w idth 100 10 1 0.1 p ppm - peak p u lse po w er (k w ) 0.1 s 1.0 s 10 s 100 s 1.0 ms 10 ms n on-repetiti v e p u lse w a v eform sho w n in fig. 3 t a = 25 c c u rrent w a v eforms t d p pk ?0.5? imp u lse exponential decay p pk t d = 7 t p t d half sine p pk s qu are t d figure 2. power derating curve l = 0.375" (9.5 mm) lead lengths t l - lead temperat u re (c) 100 75 25 0 0 50 100 150 175 peak po w er (single p u lse) t j = initial temperat u re po w er dissipation percentage of rated po w er ( % ) 50 25 75 125 www..net
sac5.0 thru sac50 vishay general semiconductor document number: 88379 revision: 20-oct-08 for technical questions within your r egion, please contact one of the following: pdd-americas@vishay.com , pdd-asia@vishay.com , pdd-europe@vishay.com www.vishay.com 3 schematic package outline dimensions in inches (millimeters) figure 3. pulse waveform t - time (ms) 150 50 0 0 2.0 4.0 i ppm - peak p u lse c u rrent, % i rsm 100 1.0 3.0 peak v al u e i ppm 10/1000 s w a v eform as defined b y r.e.a. half v al u e - i ppm i pp 2 t j = 25 c p u lse w idth (t d ) is defined as the point w here the peak c u rrent decays to 50 % of i ppm t r = 10 s t d figure 4. ac line protection application lo w capacitance t v s application note: de v ice m u st b e u sed w ith t w o u nits in parallel, opposite in polarity as sho w n in circ u it for ac signal line protection. diode transient v oltage s u ppressor do-204ac (do-15) 0.034 (0. 8 6) 0.02 8 (0.71) dia. 0.140 (3.6) 0.104 (2.6) dia. 1.0 (25.4) mi n . 0.300 (7.6) 0.230 (5. 8 ) 1.0 (25.4) mi n . www..net
document number: 91000 www.vishay.com revision: 18-jul-08 1 disclaimer legal disclaimer notice vishay all product specifications and data are subject to change without notice. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, ?vishay?), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. vishay disclaims any and all li ability arising out of the use or application of any product describ ed herein or of any information provided herein to the maximum extent permit ted by law. the product specifications do not expand or otherwise modify vishay?s terms and conditions of purcha se, including but not limited to the warranty expressed therein, which apply to these products. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of vishay. the products shown herein are not designed for use in medi cal, life-saving, or life-sustaining applications unless otherwise expressly indicated. customers using or selling vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify vishay for any damages arising or resulting from such use or sale. please contact authorized vishay personnel to obtain written terms and conditions regarding products designed for such applications. product names and markings noted herein may be trademarks of their respective owners. www..net
|
